WOrld First Boot Repair : HTC EVO 3D (HTC Shooter) Unbrick – HTC Sensation (HTC Pyramid) Unbrick - T-Mobile Samsung SGH-T989 Galaxy S II Unbrick Samsung SGH-i727 Galaxy S II Skyrocket Unbrick

 WOrld First Boot Repair : HTC EVO 3D (HTC Shooter) Unbrick – HTC Sensation (HTC Pyramid) Unbrick -  T-Mobile Samsung SGH-T989 Galaxy S II Unbrick Samsung SGH-i727 Galaxy S II Skyrocket Unbrick 


Four World First Repair Boot Released to Riff Box - Jtag Revolution

 4.03.2012    RIFF JTAG – Samsung SGH-i727 Galaxy S II Skyrocket Unbrick – Dead Boot Repair, World First ! ! ! 
Repairing bricked Samsung I727 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung I727:

•  Solder JTAG cable to Samsung I727 JTAG pads;
•  Connect USB cable to phone and PC;
•  Insert battery;
•  Make sure Samsung I727 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press Power-On.

14.03.2012   RIFF JTAG – T-Mobile Samsung SGH-T989 Galaxy S II Unbrick – Dead Boot Repair supported, World First  ! ! !
Repairing bricked Samsung T989 is easy with the RIFF Box. The device is based on the Qualcomm APQ8060 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung T989:

•  Solder JTAG cable to Samsung T989 JTAG pads;
•  Connect USB cable to phone and PC;
•  Insert battery;
•  Make sure Samsung T989 is selected in the list of models;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press Power-On.

14.03.2012   RIFF JTAG – HTC Sensation  (HTC Pyramid)  Unbrick, ModelID, CID, IMEI repair Supported
Repairing bricked HTC Sensation is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.18.0000. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG5813000’.
There is option to reflash BOOT and RECOVERY zones.
To resurrect HTC Sensation:

•  Solder JTAG cable to HTC Sensation JTAG pads;
•  Insert batter and connect USB Data cable;
•  Make sure HTC Sensation is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

14.03.2012   RIFF JTAG – HTC EVO 3D  (HTC Shooter) Unbrick – Boot Repair Supported, World First  ! ! !
Repairing bricked HTC EVO 3D (PG86300) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL version 1.49.0007. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8630000’.
There is option to reflash BOOT and RECOVERY zones.
To resurrect HTC EVO 3D:

•  Solder JTAG cable to HTC EVO 3D JTAG pads;
•  Insert batter and connect USB Data cable;
•  Make sure HTC EVO 3D is selected in the list of models;
•  If you use only battery, press Power On key;
•  Click Resurrect button;
•  Wait till software signals a successful operation completion;
•  Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:

•  Disconnect PC cable;
•  Insert battery;
•  Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

hostgator coupon free